APM Apprentice Practice Test

These questions are part of the practice quiz. Start practicing

• What is the significance of red flags or cloths on protruding materials?
• True or False: A pre job briefing form may be modified for specific jobs.
• Yellow barrier tape must be accompanied by which tag?
• What is the minimum tensile strength required for the line?
• When must reflective vests be worn?
• What kind of tag is required on a defective ladder until it is repaired or destroyed?
• What's the minimum rating required for rubber gloves when working near energized lines?
• Under what condition would a hard hat be deemed unfit for use?
• How often should offices, yards, vehicles, and job sites be kept neat and orderly?
• True or False: All lanyards used as part of a Fall Arrest System are required to be of the shock absorbing type.
• Which immediate action should be taken if a flammable liquid is spilled?
• What type of plug should office-related power cords be equipped with?
• What is the minimum length of hydraulic lines that requires the installation of check valves to prevent issues at primary voltages?
• What is the first step in atmospheric testing for confined spaces?
• What is the hazard rating category for general workplace safety?
• What does yellow barrier tape typically indicate?
• True or False: Rubber gloves must always be worn when working near exposed energized lines above 50 VAC?
• When must all employees performing non-office type work possess leather work gloves or equivalent?
• What type of protective equipment (RPE) is required before using a chainsaw?
• When should a tool rest be adjusted before using a grinder?
• What is the maximum voltage (VAC) specified for using RPE directly over uninsulated conductors or devices?
• What is the main purpose of using isolation mats during installation of RPE?
• What type of fire extinguishers are CMV fire extinguishers classified as?
• How many days in advance should you call the notification center before digging?
• What does the acronym AGKLM stand for?
• Which of the following is NOT one of the defensive driving guidelines?
• What is the maximum height you should stand on a straight ladder?
• How should non-current carrying metal parts of portable electric tools be grounded when connected to a power source?
• Which of the following is NOT included in the APM list of manholes?
• What is the correct sequence for removing insulating blankets from wires?
• True or False: It is acceptable to use a chair or desk as a substitute for a ladder.
• What must be done before the first use and every 12 months thereafter for RPE?
• Which wires should be protected first when installing insulating blankets?
• What type of liquids are mentioned as requiring eye protection when present in the workplace?
• Yellow Barrier Tape is typically used to define which type of areas?
• A pre job briefing checklist cannot be retained in which location?
• What should work areas be kept free from for safety?
• Which hard hat design is classified as Type 1?
• What are the correct classifications for hard hats?
• In what situations is wearing a hard hat required?
• What is the proper storage method for flammable and combustible liquid containers?
• Who approves specialty tools for use in the workplace?
• What does RPE stand for in safety equipment?
• In which scenario is it permissible to skip a pre job briefing?
• True or False: Following safety instructions is optional for experienced employees.
• How often should fire extinguishers in company vehicles be inspected?
• What is the requirement regarding hand protection for workers exposed to hazards?
• What should be done if a powder actuated tool misfires?
• What is the required visibility for equipment or materials projecting beyond any vehicle?
• What does DVIR stand for?
• How often should rubber protective equipment (RPE) be tested according to the guidelines?
• Which of the following is NOT a preventive event technique?
• What type of potential injury requires the use of eye protection?
• What is the main purpose of using hard hats in hazardous work areas?
• How often should all cushions and foam components of ear muffs be replaced?
• What is the minimum diameter required for the line mentioned in the requirements?
• Which of the following is NOT an acceptable method for inspecting a hard hat suspension?
• Under what conditions should safety glasses be replaced immediately?
• How often should the internal suspension of a hard hat be replaced?
• What is the required knowledge before using jibs, harnesses and slings?
• Which of the following should NOT be on a hard hat shell during an inspection?
• What is the maximum distance a tool rest should be adjusted to prior to usage on bench and pedestal grinders?
• Which action is incorrect when working at a location with an unrestrained dog in the yard?
• When starting a chainsaw, what is the safer practice regarding drop starting?
• Which of the following is NOT one of the five leading causes of accidents?
• What types of stickers are permitted on an APS hard hat?
• Which of the following is NOT a requirement for using a stepladder?
• How often should the winch line be turned end to end or rotated?
• Which type of gloves should be used when working with sharp tools?
• What action should be taken if the insulating value of RPE is suspected to be compromised?
• Which component of a hard hat should be inspected for cracks and general wear?
• How often should a hard hat be replaced regardless of its condition?
• What must red barrier tape be accompanied by?
• What should be a priority when organizing an office or job site?
• What is the maximum speed limit for vehicles in the yard area?
• A recordable injury does NOT include which of the following?
• Which of the following is not a critical element of a pre-job brief?
• What is the maximum voltage (VAC) that insulating blankets provide protection for?
• When is it acceptable to use metallic tape measures?
• What must employees do if they suspect the presence of hazardous materials?
• In environments with sound levels exceeding which decibel level is hearing protection required?
• How frequently should the insulated portion of aerial units be inspected?
• What type of lenses must safety glasses have?
• What should you do after checking for oxygen levels in a confined space?
• At what height must a safety cage begin on a fixed ladder exceeding 20 feet?
• What type of tag is indicated by the presence of red barrier tape?
• For how many days must the DVIR be retained by the department leader?
• How frequently should first aid kits be inspected to ensure adequate contents?
• Approved hearing protection should be worn in areas where the sound level reaches or exceeds what level?
• How far must a portable eyewash station or full body shower be from a chemical exposure?
• Which cleaning method is appropriate for a hard hat?
• Which guideline is NOT part of the pre-job brief?
• What is one requirement for straight ladders regarding their extension above support?
• Tools intended to be used with a safety guard must not be used if what is missing?
• What should the pre-job brief documentation include about the leading employee?
• What type of mats are required for protection when installing RPE over uninsulated conductors?
• What is the minimum clearance required in front of breaker panels for access?
• What is the minimum aisle width that should be maintained inside all buildings?
• What is the meaning of PPE?
• What should be done if a worker is exposed to potential hazards?
• What aspect of the hard hat should be examined for dents during an inspection?
• Which of the following represents 'Commercial Drivers License'?
• If a powder actuated tool misfires, what is the correct procedure to follow?
• For hand digging, how far must you dig around any identified utility?
• What does the acronym S.T.A.R. stand for?
• High power load appliances should not be plugged into which of the following?
• What safety equipment must be used when storing sharp edged and pointed tools?
• Is it true that ARC Rated clothing can be laundered like normal laundry?
• What action should be taken if a ladders is found defective?
• Is it mandatory to wear a hard hat while sitting in the cab of a truck?
• When traveling with a forklift, at what level should the forks be carried?
• Which of the following is a leading cause of workplace accidents related to knowledge and skills?
• Who is responsible for approving common tools used in the workplace?
• What is the minimum voltage at which RPE can be used safely over uninsulated conductors?
• True or False: Air-operated tools should be disconnected from the supply when not in use.
• When should additional pre-job briefings be conducted?
• How far ahead should a driver pay attention to the roadway?
• Who should you contact after an accident involving a company vehicle?
• What is classified as a close call?
• What is a sign of wear that should be checked on the suspension of a hard hat?
• What category does protective eyewear fall under?
• What arc rated hazard rating category is associated with specific safety measures?
• Transmission and Distribution field workers are recommended to replace their hard hats every ______ years.
• Where should hot hoists and their handles be stored when not in use?
• True or False: Attendants are required for all entries into manholes and vaults regardless of permit type?
• How often should visual inspections be performed on CMV fire extinguishers?
• What defines a confined space?
• How far away is smoking prohibited from doors, windows, or ventilation systems of any building?
• Insulating covers are used for protection on equipment energized at what maximum voltage?
• Which statement is true regarding pre-job briefings before repetitive tasks?
• Is it permissible to dig without a valid blue stake ticket if there are no visible conflicts?
• If a worker has their first aid treated, what category does it fall under?
• Which of the following should not be worn in a working area with overhead obstructions?
• Which voltage level indicates that MAD applies when working?
• Before which event should hard hats be inspected and field tested?
• Red barrier tape is used for what type of devices or areas?
• What are the required guidelines to document on a pre-job brief form?
• What should be done if an incident occurs regarding a company vehicle?
• How many times the maximum intended load must scaffolding support wires be rated for?
• True or False: It is permissible to start or continue work if biological materials are present, as long as a reasonable distance is maintained.
• What tool is recommended for removing approved protective devices?
• What should be your first priority regarding emergency medical treatment guidelines?
• When working with voltages between which ranges should appropriate rated gloves be worn?
• What is the proper way to connect extension cords and power strips?
• What should you look for when visually inspecting power tools before use?
• Which organization is responsible for Occupational Safety and Health Administration?
• Where should fiberglass ladders be stored to ensure their longevity?
• What item should be used to remove protective devices safely?
• When backing a class 13 or larger vehicle, how many spotters should be assigned?
• What is NOT considered when selecting personal protective equipment (PPE) for specific jobs?
• Which of these is NOT a type of energy source listed?
• What is required for pre-job briefings when two or more employees perform non-office type work?
• Who is responsible for conducting pre-job briefings?
• Which of the following actions is NOT part of the emergency response protocol?
• True or False: Consultation with Health Services is required before seeking treatment from a medical provider.
• What does red barrier tape indicate?
• What is the first step in reporting uncontrolled fires to the appropriate emergency response agency?
• How close should the tongue guard be adjusted prior to the use of grinders equipped with tongue guards?
• At what voltage level (VAC) phase to phase must approved protective devices be used?
• What aspect of barriers does red barrier tape relate to?
• Which acronym refers to Environmental Protection Agency?
• True or False: Power should always be disconnected by pulling on the cord and not using the plug.
• What is the minimum load support requirement for wires or ropes used for scaffold suspension?
• What is the role of check valves in hydraulic lines longer than 35 feet?
• What type of ventilation should be used to make a confined space safe before entry?
• What is the maximum diameter for stickers that can be placed on hard hats?
• What is an important aspect to allow during a pre-job brief?
• How should portable electric tools be connected to a power source for safety?
• What is recommended for safety glasses to ensure they are durable?
• How often should the suspension component of a hard hat be replaced?
• Which potential hazard is related to the use of protective eyewear?
• What is the minimum standard for safety glasses as marked by ANSI?
• What should be identified during a pre-job brief regarding the job?
• Which type of receptacle needs ground fault circuit interrupter protection during temporary wiring installations?
• Insulating blankets are required for protection on lines energized up to what voltage between phases?
• How often should hearing tests be performed to ensure safety standards are met?
• What is the longest duration that RPE can remain in place on energized lines without approval?
• What is the safety boot requirement specification?
• What should be posted when backing a vehicle?
• When should gloves NOT be worn according to safety guidelines?
• Which safety requirement is necessary when using a straight ladder?
• What type of hazards does the acronym RPE primarily address?
• What is a condition under which wearing PPE may not be necessary according to the APM?
• Which of the following is a principle of defensive driving?
• If you observe an unsafe condition or practice and are unable to rectify it, what should you do?
• What defects should be looked for when inspecting the shell of a hard hat?
• Which of the following methods is NOT recommended for decorating a hard hat?
• Before using a chainsaw, which specific piece of personal protective equipment should be worn?
• To reduce the possibility of chainsaw kickback, which practice should be followed?
• Class 0 gloves are rated for which voltage?
• What does Yellow Barrier Tape signify in a construction or maintenance environment?
• True or False: Every employee must observe all rules and practices and follow their leader's instructions.
• In areas with exposed energized equipment, which type of tape measure should not be used?
• How often should the mechanical tests be performed?
• What does SDS stand for in safety documentation?
• How often should rubber insulating gloves be tested according to the established protocol?
• True or False: You can carry a cup of coffee down the stairways.
• What should be the focus of visual inspections for power tools?
• How frequently should Class 2 gloves be retested?
• True or False: The power should never be disconnected by pulling the cord; instead, the tool should be pulled.
• What is a common electrical hazard that requires hard hat usage?
• What should be avoided to minimize chainsaw kickback while operating?
• What is another name for the One Call Notification Center which must be contacted prior to digging?
• What is the recommended testing period for electrical tests?